Automatic Transformer Tester Turn Ratio & LCR Meter 200KHz 15025 Points 2in1 USB

Description

TH2832XA
Model
TH2832XA
Transformer test system
Transformer testing parameters
Turn Ratio, Turns,
Phase,
L, C, Lk, Q
,
ACR
,
DCR
,
Balance,
Pin Short.
Basic accuracy
LCRZ
0.1%
DCR,Turn Ratio
0.5%
Test signal level
20Hz-200kHz, total
15025 points
Signal source output impedance
30
Ω, 100Ω
AC test signal level
Normal
10mV
—2Vrms
Min. resolution: 10mV,accuracy：10% x setting voltage+2mV
100
μA—20mArms
Min. resolution:
0.1mA
Constant level
20mV
—1Vrms
Min. resolution:
10mV,
accuracy:
10% x setting voltage+2mV
200
μA—10mArms
Min. resolution:
0.1mA
DC bias voltage source
0V -
±
5V
Min. resolution:
0.5mV,
accuracy：1% x setting voltage+5mV
0mA -
±50mA
Min. resolution:
0.5μA
LCR testing parameters
|Z|,|Y|,C,L,X,B,R,G,D,Q,
θ,DCR
DCR display range
0.00001
Ω - 999.999MΩ
Turn Ratio display range
1:0.01 -
100:1
LCR display range
|Z|,R,X
0.00001
Ω-99.9999MΩ
|Y|,G,B
0.00001
μs-99.9999s
C
0.00001pF-
9.99999F
L
0.00001
μH-99.9999kH
D
0.00001-
9.99999
Q
0.00001-
99999.9
θ(DEG)
-179.999
º-179.999º
θ(RAD)
-3.14159-
3.14159
Δ%
-999.999%-
999.999%
Test time(≥10 kHz)
Fast: 25 times/second（40ms）,Med: 8 times/second（125ms）,Slow：2.7 times/second（370ms）
Equivalent circuit
Series, Parallel
Range mode
Auto, Hold
Trigger mode
Internal, Manual, External, Bus
Average
1-
255
Zero clear function
Open circuit, short circuit, load
Mathematics
Direct,ΔABS,Δ%
Set time for trigger delay
0-
60.000s, step 1ms
Set time for step delay
0-
60.000s, step 1ms
Comparator
10 bins,
BIN1-BIN9, NG, AUX
Bin counting
PASS,
FAIL front pannel or scan fixture LED display
Storage
100 groups for LCR and 100 groups for transformer scan
Interface
HANDLER
or SCANNER
USB HOST,
RS232C, RS485(optional), GPIB(optional)
USBDEVICE
TH1831
scanning test fixture
Scanning test output pins
24Pin
Distribution capacitance at 24 Pin
scan output terminals
20pF
Transformer locking device（optional）
Pneumatic (TH1831-02) support max. 0.7MPa
Manual (TH1831-01)
Pannel test control
START
，RESET，PASS/FAIL LED display
Handler
input/output signal from scanning fixtures
power supply：+5V，GND input: START，RESET output: PASS，FAIL on-off signal
TTL level
Eternal input
foot switch
Temperature and Humidity
0C
-40C，≤90%RH
solenoid valve power output
+24V
Size
228mmx
203mmx53
mm
Weight
2.9kg
Accessories:
TH1831
scanning test fixture, power cord (US, Euro, Au or UK plug is available)